思科路由器密码分为五种:
密码种类用途控制台端口密码(line)通过控制台端口进入用户模式辅助端口密码(line aux)通过辅助端口进入用户模式Telnet密码(line vty)通过Telnet进入用户模式启用密码(enable)控制用户进入特权模式,用于老式系统启用加密密码(enable secret)控制用户进入特权模式 1、启用密码和启用加密密码在全局配置模式下:
启用密码(10.3之前的老式系统):
启用加密密码(区分大小写):
R1(config)#enable secret Password我们现在一般采用启用加密,示例:
R1#conf tR1(config)#enable secret 12345R1(config)#^ZR1#disableR1>enPassword: R1#从用户模式进入特权模式时我们需要敲enable,如果设置了上面两个密码其中一个,那么在敲enable时提示输入密码。
他俩功能一样,但secret密码比password密码大一点,如果设置了secret密码,password密码就失效了。
辅助密码是对Cisco 路由器背面的辅助端口加密的密码,如果设置了辅助密码,那么通过辅助端口连接Cisco路由器时将要求输入正确的密码。
辅助端口是给用户通过调制解调器(modem)来连接路由器用的。
控制台console,就是我们用PC机通过超级终端和Cisco路由器连接的端口。它在路由器后面,要通过翻转电缆和PC连接。
R1(config)#line console 0R1(config-line)#password PasswordR1(config-line)#login还有两个命令:
exec-timeout 0 0 //将控制台EXEC超时时间设为0,意味着永远不超时。默认为10分钟logging synchronous //避免不断出现控制台消息(具体配置模式下) 4、Telnet密码我们通过Telnet连上Cisco路由器时,被要求输入密码。
R1(config)#line vty 0 ?<1-190> Last Line number<cr>R1(config)#line vty 0 190 //允许同时有191个终端远程登陆R1(config-line)#password PasswordR1(config-line)#login当然,你也可以通过no login命令路由器允许建立无口令验证的telnet连接,只要你不担心安全方面的问题。
5、设置SSH补充一下,我们推荐使用SSH而不是Telnet,因为SSH使用加密密钥来发送数据,而Telnet使用非加密数据流明文发送用户名和密码。
Router(config)#hostname R1R1(config)#ip domain-name 123.com //设置域名R1(config)#username R1 password 123 R1(config)#crypto key generate rsa //生成保护会话的加密密钥The name for the keys will be: R1.123.comChoose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes.How many bits in the modulus [512]: 1024% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]R1(config)#*Mar 1 04:22:08.826: %SSH-5-ENABLED: SSH 1.99 has been enabledR1(config)#ip ssh version 2 //启用SSH第2版R1(config)#line vty 0 190R1(config-line)#transport input ssh //也可以带上telnet 6、对密码加密默认情况下,只有启用加密密码是加密的,要对用户模式密码和启用密码加密,需要手工配置。
执行show running-config命令时,将看到除启用加密密码外的其他所有密码,通过service password-encryption命令来给它们加密。